background image

MN008006EN Manual 

Efective March 2021 

NOVA LBS Load Break Switch  

16 

www.eaton.com/cooperpowerseries 

 

 

 

CAUTION 

 

Equipment misoperation. Verify all connector pins and both mating 

interface surfaces are clean and dry before connecting cables. Voltage 

sensing errors can result from contamination. Failure to comply can 

result in control and switch misoperation. 
 
The electrical connectors of the switch, control, and cable must be clean 

and dry. Contaminated surfaces may be cleaned with denatured alcohol 

and wet connector surfaces may be dried with a heat gun. Dry surfaces 

are particularly important for the internal voltage sensor cable 

connections. The accuracy of the sensors can be influenced by moisture 

contamination. 

 

CAUTION 

 

Equipment misoperation. Do not connect this control to an energized 

switch until all control settings have been properly programmed and 

verified. Refer to the programming information for this control. Failure 

to comply can result in control and switch misoperation, equipment 

damage, and personal injury. 
Connect control cables, power cables, and sensor cables to the control. 

Verify that the proper cable/receptacle connections are made. Improper 

cable connections can result in damage to the switch and/or control.  
Complete the control programming before making the high-voltage line 

connections. Refer to the Operation section of this manual. Verify the 

correct voltage rating of the equipment. Verify the correct control 

programming for ratio and phase angle correction for the voltage rating 

of the equipment. 
Make appropriate electrical connections to the terminals of the switch. 

Verify the correct load-side (vertical bushings) and source-side 

(horizontal bushings) terminal connections. This is required for correct 

operation of the internal voltage sensor. Energize switch and confirm 

the voltage outputs in the control. 
When the switch is energized, the output signal from the voltage 

sensors sent to the control is 20 to 40 V (depending on the primary 

voltage). 

Operation 

TABLE 7 - Phase angle adjustment / Voltage sensor ratio adjustment

 

Sensor 

Switch 

Cable lenght 

Voltage sensor 

ratio adjustment 

Phase shift 

Capacitive 

NOVA LBS 15 / 27 

3 m 

6 m 

9 m 

12 m 

15 m 

727:1 

731:1 

732:1 

735:1 

740:1 

-2° 

-2° 

-2° 

-2° 

-2° 

 

LBC control settings 

The LBC control must be programmed with the TP ratio and phase angle 

setting as per TABLE 7. These are inserted in the System Setup screen 

(Figure 17). 
 
See Manual MN008008 for more information about programming the 

LBC control. 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for NOVA LBS 15


























Reviews: