background image

MN008006EN Manual 

Efective March 2021    

NOVA LBS Load Break Switch 

www.eaton.com/cooperpowerseries 

15 

 

 

VOLTAGE SENSING OPTION 

 

Installation 

 

ADVERTISEMENT 

 

Hazardous voltage. Always use a hotstick when working with this 

equipment. Failure to do so could result in contact with high voltage, 

which will cause death or severe personal injury. 
 

 

ADVERTISEMENT 

 

Hazardous voltage. Always use a hotstick when working with this 

equipment. Failure to do so could result in contact with high voltage, 

which will cause death or severe personal injury. 

 

ADVERTISEMENT 

 

Hazardous voltage. Solidly ground all equipment. Failure to comply can 

result in death, severe personal injury, and equipment damage. 
 

 

IMPORTANT 

 

Disconnect switches for AC control power are necessary to isolate the 

control for testing and servicing. 
 

 

ADVERTISEMENT 

 

Hazardous voltage. If terminal connections are reversed, the internal 

voltage sensing option may indicate zero voltage with the contacts 

open. Do not rely on internal voltage sensing to ensure that the voltage 

is zero and the line has been de-energized. Always follow proper safety 

practices and use a separate detection method to verify a de-energized 

condition. Failure to do so can result in contact with high voltage, which 

will cause death or severe personal injury. 
 

 

CAUTION 

 

Equipment damage may occur if torque values are exceeded. 
 
The Internal voltage sensing uses a capacitive voltage divider to provide 

a low voltage input to the NOVA LBS switch control. 
Refer to the Installation section of this manual for the installation 

procedure for the NOVA LBS. 
 
See manual MN008007 for more information on installing the LBC Pole 

Mount control. Make the internal voltage sensing option connections 

when installing the control as indicated in these Service Information 

manuals. 
Verify correct grounding of the NOVA switch and control prior to 

making any high-voltage connections and before high-potential testing. 

A proper ground connection consists of a good electrical ground 

connection to the surge ground connector located on the mechanism 

housing. Provide a good electrical ground connection to the control 

cabinet ground. 

Note

: Painted surfaces of the mechanism housing may prevent a ground 

connection to the switch housing. Always provide a good electrical 

connection to the mechanism surge ground connector. Poor grounding 

of the mechanism housing may result in the presence of high voltage on 

the mechanism housing associated with the high-voltage resistor or 

capacitor connections used with internal voltage sensing. 
 
To ensure proper installation of this cable, securely fasten the aluminum 

cable coupler ring. 
 
 
 
 
 
 
 
 
 
 
 

Figure 15.

 Receptacle for NOVA LBS cable. 

 

 

CAUTION 

 

Dangerous voltage. Do not touch the voltage measurement/control 

cable receptacle connections. If the NOVA LBS Load Break Switch is 

energized and the voltage measurement/control cable is disconnected 

from the Load Break Switch or control, a voltage will be present at the 

receptacle. Contact with this voltage can cause personal injury. 
 
The NOVA LBS switch has a 19-pin male receptacle (Figure 15) that 

connects to the control via a shielded 19-pines cable. The control has a 

19-pin female receptacle and its corresponding circuitry; see Figure 16. 
 
The LBC control has a 4-pin male receptacle (Figure 16) that connects to 

the Potential Transformer via a shielded 4-conductor cable. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Figure 16.

 Connections of the LBS Control 

Grounding 

conector 

19-pin receptacle 

for 19-pin cable. 

Cable glands for 

connecting 

external control / 

antenna cables 

Receptacle for 

power supply 

cable 

Summary of Contents for NOVA LBS 15


























Reviews: