manualshive.com logo in svg

Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN, Hardware And Engineering

Share
Download
Eaton Moeller SmartWire-Darwin EU5C-SWD-CAN Hardware And Engineering Download Page 19

Mounting

15

02/09 AWB2723-1612en

Potential Relationship between the Components

The entire SmartWire-Darwin system operates on a common 
supply voltage. Provide a common star point for the earth 
wiring. In this way the various slaves in the SmartWire-
Darwin system will not be electrically isolated from one 
another. The field bus and the SmartWire-Darwin system are 
electrically isolated from one another.

Connection SmartWire Darwin

X

Connect the SmartWire-Darwin network via the 8-pole 
SmartWire-Darwin cable. To do so use the SmartWire-
Darwin cable SWD-4-100LF8-24 and the relevant blade 
terminal SWD-4- 8MF2 or prefabricated cables of the type 
SWD-4-(3/5/10)F8-24-2S.

j

Warning!

Switch off the power supply, if you are reconnecting slaves 
in the SmartWire-Darwin system or reconnecting the 
ribbon cable connection. Otherwise the SmartWire-
Darwin slaves can be destroyed!

j

Warning!

The gateway has protection against polarity reversal for 
the 24-V-DC-POW supply. However, if the gateway is 
connected via the serial interface to an earthed device (for 
example to a PC), the gateway can be destroyed, if the 
polarity of the power supply is reversed!

Summary of Contents for Moeller SmartWire-Darwin EU5C-SWD-CAN













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands