Eaton Matrix Telecom Inverter System Installation And Operation Manual Download Page 11

Page: 11 / 86

General Description

IPN 997-00012-68D February 2010

Part Numbers

Part Number

Description

INV-4810E

1000VA/800W inverter module
(I/P: 48Vdc, O/P: 230Vac, 1U*5U)

INV-4810

1000VA/800W inverter module
(I/P: 48Vdc, O/P: 120Vac, 1U*5U)

INV-4815E

1500VA/1200W inverter module
(I/P: 48Vdc, O/P: 230Vac, 1U*5U)

INV-4815

1500VA/1200W inverter module
(I/P: 48Vdc, O/P: 120Vac, 1U*5U)

INV-STS-050

6kVA/12kVA static transfer switch module (50A, 1U*5U)

INV-STS-100

12kVA/18kVA static transfer switch module (100A, 2U*5U)

INV-MC-1000

Controller module (LCD, 3*LED, 4*function key, 1U*2U)

INV-IFC-1000

RS232/USB interface module (1U*3U)

INV-SS-2-1U

19-inch inverter “hot-swap” chassis (1U)

INV-STSSS-1U

19-inch controller/STS “hot-swap” chassis for 50A STS (1U)

INV-STSSS-2U

19-inch controller/STS “hot-swap” chassis for 100A STS (2U)

INV-MBSDU-50

50A Maintenance Bypass, AC Distribution Panel (2U)

INV-MBS-100

100A Maintenance Bypass Panel (2U)

INV-IFP-15 Inverter/STS

Blank

Panel

INV-RFP-12

Controller Blank Panel

INV-CFP-13

Interface Blank Panel

Summary of Contents for Matrix Telecom Inverter System















































































Search results

Summary of Contents for Matrix Telecom Inverter System

Reviews:

Related manuals for Matrix Telecom Inverter System

Brands by name

Popular brands

Eaton Matrix Telecom Inverter System, Installation And Operation Manual

Search results

Summary of Contents for Matrix Telecom Inverter System

Reviews:

Related manuals for Matrix Telecom Inverter System

Brands by name

Popular brands