Capitole 40
50 1991.901 G01 002
3.4.2 Modification of a withdrawable version
of the assembly
General
This paragraph describes the modification of the cubicle
layout with outgoing feeders in the withdrawable version.
The standard version of a cubicle consists of sixteen units
each being 125 mm high and 500 mm wide.
From these units a cubicle may be constructed with
compartments each provided with draw-out units of 1x125
mm up to a maximum of 16.
If it is desired the layout of a cubicle can be changed. One
standard (size 125 mm) compartment can be split into two
smaller sized drawers.
The modification of the cubicle layout can be done in a
simple way. There are four possibilities:
a.
Changing a number of small compartments into one
large compartment, see below.
b.
Changing one large compartment into a number of
small compartments, see page 51.
c.
Changing one split-up compartment with two or
three draw-out units into one compartment with one draw-
out unit, see page 51.
d.
Changing a compartment with one draw-out unit
into a split-up compartment with two or three draw-out
units, see page 57.
a.
Changing a number of small compartments
into one large compartment
•
Remove the doors of the compartment concerned by
removing thehexagonal socket-head bolts from the
hinges.
•
Then remove the insulated screening-plate between the
cable-compartment and the draw-out unit compartment
by turning the quick-locking device through 90°.
•
Remove the secondary wiring and the main cable.
•
The horizontal dividing-plate can be slid out after the
twofastening bolts in the frontal upright have been
removed.
•
The large door and the screening-plate may then be
fitted.
b.
Changing one large compartment into a
number of small compartments
•
Remove the large door and screening-plate as
described above.
•
Fit the necessary horizontal dividing-plates.
A
TTENTION
Ensure that the horizontal dividing-plates are
positioned in the correct slots, at the back of the
cubicle.
•
Fit the necessary doors and screening-plates.
Summary of Contents for Holec Capitole 40
