Questions?/ Des questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
1
Instruction Manual / Manuel d’instructions/ Instrucciones
PACKAGING CONTENTS /CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
ENGLISH
A.
Fixture housing
Boîtier de l’appareil
Alojamiento del
portalámparas
B.
(2) Lampholder gaskets
(2) Joints statiques de
douille
(2) Juntas obturadoras
del receptáculo
C.
(2) #6-32 x 3/4 in. and (2) #8-32 x 3/4
in. junction box screws (use the size
that fits your junction box)
(2) vis nº 6 de 32 x 3/4 po et 2 vis nº 8
de 32 x 3/4 po pou boîtier de jonction
(choisissez la dimension convenant
à votre boîtier de jonction)
(2) Tornillos #6-32 x 3/4 pulg. y (2)
tornillos #8-32 x 3/4 pulg. para
montaje de la caja de conexiónes
(utilice el tamaño que mejor se
adecue a su caja de conexiónes)
D.
(2) Wire nuts
(2) capuchons de
connexion
(2) Tuercas
para alambre
PWT250PC
PWT250PCH
(Bronze/Bronce)
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Punch
• Hammer
• Weatherproof silicone caulking
• Wire connectors
• (2) 150 watt (MAX) PAR 38 floodlight bulbs
NOTE:
This fixture was designed to work with up to 150 watt maximum PAR Halogen flood
bulbs. For improved energy efficiency, lower wattage PAR Halogen flood bulbs may be used.
Compact Fluorescent (CFL) bulbs contain electronics which may interfere with the light-
sensing function of your dusk to dawn fixture and are not recommended.
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location use.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• To reduce the risk of a burn during relamping, disconnect power supply to the unit
before relamping.
• The bulb and fixture get extremely hot during use. Allow fixture to cool completely
before attempting to reposition fixture.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Disconnect power and allow fixture to cool before changing bulb or handling fixture.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Mount fixture to a grounded junction box marked for use in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground
mount installation.
• Keep away from flammable objects. Do not position fixture within
two inches of any combustible materials.
• Always use or replace bulb with the same wattage or lower wattage than required.
Installing a bulb of a higher wattage could create a fire hazard and will void
the warranty.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• Fixture heads must be aimed in a downward direction. Aiming the fixture heads
upward can result in accumulation of water in the fixture and will void the warranty.
SAVE THESE INSTRUCTIONS.
INSTALLING YOUR FIXTURE
CAUTION:
Always turn off power at fuse box or circuit breaker before
removing or installing any light fixture.
1. This mounting plate has been designed to work with a variety of different junction boxes.
Line up the knockout holes in the mounting plate with the screw locations in your junction
box. Drill out the matching holes in the mounting plate using an electric drill and a 1/8˝
drill bit or knock out the holes with a punch and hammer.
2. Take the gasket included with this mounting plate and position it behind the mounting
plate. Line up the screws in the mounting plate with the appropriate hole pattern in the
gasket and remove gasket material in those holes.
3.
Connect lampholder wires to supply wires from house (white to white and black to
black) using wire connectors.
4. Attach the mounting plate to your junction box using the screws (D), making sure that the
gasket is properly aligned and that all screws are
tightly secured. To prevent moisture from entering the junction box, apply a bead of
silicone sealant around the edge of the mounting plate where it attaches to the
junction box.
WARNING:
Do not touch fixture during use as the fixture housing gets extremely hot. Turn off
fixture and allow to cool before replacing bulb.
AIMING THE LIGHT
Loosen the knob on the side of the light housing. Tilt fixture head up or down to desired
position then retighten knob.
WARNING:
Risk of fire/electric shock. Follow installation instructions carefully.
SAVE THESE INSTRUCTIONS.
PWT250PCW
PWT250PCWH
(White/Blanc/Blanco)
WARNING
