Questions?/Des questions?/¿Preguntas? 1-800-334-6871 [email protected]
1
Instruction Manual/Manuel d’instructions/Instrucciones
PACKAGING CONTENTS/CONTENU DE L’EMBALLAGE/CONTENIDO DEL PAQUETE
Instruction Manual / Manuel d’instructions/ Instrucciones
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Drill with 3/16 in. drill bit (only needed if hole pattern on coverplate does not match
junction box)
• Weatherproof silicone caulking
• (1) 150 watt (MAX) PAR 38 floodlight bulb
NOTE:
For improved energy efficiency, use lower wattage bulbs.
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location use.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassembled for easy installation.
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• To reduce the risk of a burn during relamping, disconnect power supply to the unit
before relamping.
• The bulb and fixture get extremely hot during use. Allow fixture to cool completely
before attempting to reposition fixture.
• Disconnect power at fuse or circuit breaker before installing or servicing.
• Disconnect power and allow fixture to cool before changing bulb or handling fixture.
CAUTION
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Mount fixture to a grounded junction box marked for use in wet locations.
• Suitable for wall mount or eave mount only. NOT suitable for ground
mount installation.
• Keep away from flammable objects. Do not position fixture within
two inches of any combustible materials.
• Always use or replace bulb with the same wattage or lower wattage than required.
Installing a bulb of a higher wattage could create a fire hazard and will void
the warranty.
• MINIMUM 90° C SUPPLY CONDUCTORS.
• Fixture heads must be aimed in a downward direction. Aiming the fixture heads
upward can result in accumulation of water in the fixture and will void the warranty.
SAVE THESE INSTRUCTIONS.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect power at fuse or circuit breaker before
installing or servicing.
NOTE:
Junction box must be at least 1-1/2 inch in
depth for proper installation (Fig. 1).
1.
The coverplate has been designed to work with
a variety of different junction boxes (not included).
Line up the holes in the coverplate with the screw
holes in your junction box. If holes in the coverplate
do not match the screw holes on your junction box,
drill holes in the coverplate using an 3/16 inch drill
bit to match the screw holes on the junction box.
3.
Connect the black wire from the fixture to the black house supply wire and the white wire
from the fixture to the white supply wire using wire nuts (D).
4.
Attach the ground wire coming from your house to the copper ground wire from the
fixture (A) using wire nut (D). If no house ground wire is available, attach the copper
ground wire from the fixture to the junction box if it is metal and grounded. If junction
box is not metal and no house ground wire is available, an alternative ground source
must be used for safe operation.
5.
Attach fixture to the junction box with two of the screws (C) provided. Either (2) #6 or (2)
#8 screws will work with most standard junction boxes. Make sure that all screws are
tightly secured.
6.
To prevent moisture from entering the junction box, apply a bead of silicone sealant
around the edge of the coverplate where it attaches to the junction box and any
open holes.
7.
Insert lampholder gasket (B) into lampholder and screw bulb into lampholder.
(Do not overtighten bulb.)
8
. Turn on power at main fuse/breaker box.
AIMING THE LIGHT
WARNING: Risk of electric shock. Disconnect power and allow fixture to cool before
changing bulb or handling fixture.
1.
Loosen the knob on the side of the light housing (A) and locknut on arm.
2.
Tilt fixture head to desired position and then retighten.
2-YEAR LIMITED WARRANTY
THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
Eaton warrants to customers that, for a period of two years from the date of purchase, Eaton’s
products will be free from defects in materials and workmanship. The obligation of Eaton
under this warranty is expressly limited to the provision of replacement products. This
warranty is extended only to the original purchaser of the product. A purchaser’s receipt or
ENGLISH
WARNING
MT125W
MT125WH
(White/Blanc/Blanco)
A.
Light fixture
Luminaire
Accesorio
Round
1-1/2 in.
Octagonal
1-1/2 in.
1
B.
(1) Lampholder gasket
(1) Joint statique de douille
(1) Junta obturadora del receptáculo
C.
(2) #6 and (2) #8 mounting screws
(use the size that fits your junction box)
(2) vis nº 6 et (2 )vis nº 8 pour boîte de jonction (choisissez
la dimension convenant à votre boîte de jonction)
(2) Tornillos #6 y (2) tornillos #8 de montaje (utilice el
tamaño que mejor se adecue a su caja de conexión)
D.
(3) Wire nuts
(3) capuchons de connexion
(3) Conectores del cables
MT125
MT125H
(Bronze/Bronce)
