Eaton EFX48 e-Fuse Series Installation And Operation Manual Download Page 61

Page: 61 / 161

Installation

IPN March 2019



Protective earthing conductor to protective earth wire in building.

Step 4 - Check Output Reference to Ground

The dc +ve output of the RM3-340/440 is bonded to ground internally within the unit

and is not serviceable.
The grounding arrangement of your communications equipment determines how the

dc common of the dc power system is referenced to ground. Ensure that this is

compatible with the grounding of the RM3-340/440.

Procedure complete

Task 4 - Connect the DC Load and Battery Cables



•

If the RM3-340/440 dc power system is to be installed in a location where the ambient

temperature may rise above 50ºC (122ºF), then 90°C rated cable rated cable must be used

for the dc load and battery connections.

Summary of Contents for EFX48 e-Fuse Series


























































































































































Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands

Eaton EFX48 e-Fuse Series, Installation And Operation Manual

Search results

Summary of Contents for EFX48 e-Fuse Series

Reviews:

Related manuals for EFX48 e-Fuse Series

Brands by name

Popular brands