background image

Eaton

1000 Eaton Boulevard

Cleveland, OH 44122

United States

Eaton.com

© 2020 Eaton

All Rights Reserved

Printed in USA

Publication No. IB020004EN / TBG 001498

October 2020

Eaton is a registered trademark.

All other trademarks are property  

of their respective owners.

Instructions for installation and maintenance 

of the AMPGARD Reduced Voltage Soft Starter 

  

Instruction Booklet 

IB020004EN

Effective October 2020

DISCLAIMER OF WARRANTIES AND LIMITATION OF LIABILITY

The information, recommendations, descriptions and safety nota-

tions in this document are based on Eaton Corporation’s (“Eaton”) 

experience and judgment and may not cover all contingencies. 

If further information is required, an Eaton sales office should be 

consulted. Sale of the product shown in this literature is subject 

to the terms and conditions outlined in appropriate Eaton selling 

policies or other contractual agreement between Eaton and the 

purchaser.
THERE ARE NO UNDERSTANDINGS, AGREEMENTS, WARRANTIES, 

EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF 

FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY, 

OTHER THAN THOSE SPECIFICALLY SET OUT IN ANY EXISTING 

CONTRACT BETWEEN THE PARTIES. ANY SUCH CONTRACT 

STATES THE ENTIRE OBLIGATION OF EATON. THE CONTENTS OF 

THIS DOCUMENT SHALL NOT BECOME PART OF OR MODIFY 

ANY CONTRACT BETWEEN THE PARTIES. 
In no event will Eaton be responsible to the purchaser or user in 

contract, in tort (including negligence), strict liability or other-wise 

for any special, indirect, incidental or consequential damage or loss 

whatsoever, including but not limited to damage or loss of use of 

equipment, plant or power system, cost of capital, loss of power, 

additional expenses in the use of existing power facilities, or claims 

against the purchaser or user by its customers resulting from the 

use of the information, recommendations and descriptions contained 

herein. The information contained in this manual is subject to change 

without notice. 

Summary of Contents for AMPGARD RVSS

















Reviews: