manualshive.com logo in svg

Eaton 93PM IBC-LHW, Installation Manual, Page: 68 / 78

Share
Download
Eaton 93PM IBC-LHW Installation Manual Download Page 68

58

Eaton 93PM Universal Integrated Battery Cabinet (IBC-LW and IBC-LHW) Installation Manual P-164000541—Rev 04

Figure 27. Eaton 93PM IBC-LW Standalone Power Online – One or Two Cabinets

Internal   

   Internal 

Battery          

   Battery 

Breaker   

   Breaker  

UPS Cabinet 

   Battery Cabinet 1        Battery Cabinet 2 

NOTE

External wiring to be supplied by the customer.

Figure 28. Eaton 93PM IBC-LW Standalone Power Online – Four Cabinets

External Tie
Point and 
Battery Breaker
or Disconnect

UPS Cabinet 

 

 

      Battery Cabinet 1        Battery Cabinet 2      Battery Cabinet 3       Battery Cabinet 4

Internal   

   Internal  

       Internal 

          Internal

Battery          

   Battery       

       Battery    

          Battery

Breaker   

   Breaker  

       Breaker 

          Breaker 

NOTE 1

External tie point, battery breaker or disconnect, and wiring to be supplied by the
customer.

NOTE 2

Up to eight cabinets can be paralleled with a 93PM 100-400 kW UPS.

Onelines and Schematics

Summary of Contents for 93PM IBC-LHW















































































Reviews:

No comments