manualshive.com logo in svg

Eaton 93PM 150 kW SIAC-B Three-Wire, Installation And Operation Manual, Page: 21 / 106

Share
Download
Eaton 93PM 150 kW SIAC-B Three-Wire Installation And Operation Manual Download Page 21

        Eaton 93PM Sidecar Integrated Accessory Cabinet-Bypass (150 kW and 200 kW SIAC-B) Installation and Operation Manual  P-164000387—Rev 7

 www.eaton.com/powerquality

3-1

Chapter 3

Installation Plan and Unpacking

This chapter includes planning for the Eaton 93PM 150 kW and 200 kW Sidecar Integrated Accessory 
Cabinet-Bypass (SIAC-B).

Use the following basic sequence of steps to install the SIAC-B:

1.

Create an installation plan for the SIAC-B.

2.

Prepare your site for the SIAC-B.

3.

Inspect and unpack the SIAC-B (refer to the applicable Eaton 93PM UPS Installation and Operation 
manual, listed in paragraph 1.7, for inspection and unpacking instructions).

4.

Unload and install the SIAC-B (refer to the applicable Eaton 93PM UPS Installation and Operation manual, 
listed in paragraph 1.7, for inspection and unpacking instructions).

5.

Externally wire the SIAC-B.

6.

Complete the Installation Checklist.

7.

Have authorized service personnel perform preliminary operational checks and start up the system.

3.1

Creating an Installation Plan

Before installing the SIAC-B, read and understand how this manual applies to the system being installed. Use 
the procedures and illustrations in this section to create a logical plan for installing the SIAC-B.

3.2

Preparing the Site

For the UPS system to operate at peak efficiency, the installation site should meet the environmental 
parameters outlined in this manual. The operating environment must meet the weight, clearance, and 
environmental requirements specified for the applicable accessory cabinet. Specifications subject to change.

3.2.1

Environmental and Installation Considerations

The UPS system installation, including the SIAC-B, must meet the following guidelines:

l

The system must be installed on a level floor suitable for computer or electronic equipment.

l

The system must be operated at an altitude no higher than 1500m (5000 ft) without derating. For additional 
assistance with high altitude operation, contact an Eaton service representative (see paragraph 1.8).

l

The system must be installed in a temperature and humidity controlled indoor area free of conductive 
contaminants.

Failure to follow guidelines may void your warranty.

NOTE

The SIAC-B is attached to and directly integrated with the UPS cabinet at the factory 
or after field installation on sight. This section must be used along with the 
applicable Eaton 93PM UPS Installation and Operation manual, listed in paragraph 
1.7, during installation planning and unpacking.

NOTE

Startup and operational checks must be performed by an authorized Eaton 
Customer Service Engineer, or the warranty terms specified on page W-1 become 
void. This service is offered as part of the sales contract for the UPS. Contact an 
Eaton service representative in advance (usually a two-week notice is required) to 
reserve a preferred startup date.

Summary of Contents for 93PM 150 kW SIAC-B Three-Wire











































































































Reviews:

No comments