background image

 

Table 1:

 

 

 

Item

 

 

Submenu

 

 
 

 
 

 

1. Installer Setup

 

 

1.  ID Code                         [1]

 

2.  Unlock Timing               [05]

 

3.  Unlock Output               [0]

 

4.  Card Memory                [0]

 

5.  Doorplate Mode

 

6.  Audio Options ...

 

7.  Parameters ...

 

8.  Installer Code ...

 

9.  Default ...

 

 
 
 
 

 

2. Setup

 

1.  Language                     [1]

 

2.  Tone Select                  [03]

 

3.  Tone Volume                [08]

 

4.  Unlock Code                [1111]

 

5.  Display Mode 

 

6.  Clock ...

 

7.  Setup Code ...

 

8.  About ...

 

9.  Default ...

 

 
 

 

3. Card Manage

 

 

1.  Add Card ...

 

2.  Delete By Card

 

3.  Delete By M.code

 

4.  Cards Information

 

5.  Format

 

 

4. Online Monitors

 

 

To  search  the  online  monitors,input  the  monitor  code 

 

number to search

 

 

5. Online Devices

 

 

To  search  the  online  door  stations.Max.4  door  station 

 

can be searched

 

 

6. Voltage Measure

 

 

To  check  the  voltage  of  the  monitor,note  that  the 

 

monitor must be online.

 

Summary of Contents for DJ LCD ID




















Reviews: