Eastwood 33862 Instructions Manual Download Page 5 | Manualshive

Page: 5 / 8

Eastwood 33862 Instructions Manual Download Page 5

To order parts and supplies: 800.343.9353 >> eastwood.com

5

THREAD CUTTING

CUTTING INTERNAL THREADS WITH A TAP

• Consult the included Tap Drill Guide and drill the appropriate tap hole size.

(Tap drills not included).

• Apply a generous amount of cutting oil to the Tap.
• Insert the Tap into the bored hole and begin turning with a steady, even pressure. Keep the Tap

straight in the bore. If excessive resistance is felt, stop immediately to avoid breaking a Tap.

• Typical tapping procedure is one revolution then back out 1/2 turn to release chips.
• When the tapping operation is complete, slowly, and steadily back out the Tap.

CUTTING EXTERNAL THREADS WITH A DIE

• Consult the included Tap Drill Guide and drill the appropriate tap hole size. (Tap drills not

included).

• Apply a generous amount of cutting oil to the Tap.
• Insert the Tap into the bored hole and begin turning with a steady, even pressure. Keep the Tap

straight in the bore. If excessive resistance is felt, stop immediately to avoid breaking a Tap.

• Typical tapping procedure is one revolution then back out 1/2 turn to release chips.
• When the tapping operation is complete, slowly, and steadily back out the Tap.

«
...
3
4
5
6
7
...
»

Summary of Contents for 33862









Reviews:

No comments