EASTMAN Kodak X-Omat 180 LP Installation Instructions Manual Download Page 39

Page: 39 / 42

Checking for Correct Operation

1C7836 – February 1996

Continuing to Check the Components

[1] Enter the “Automatic Mode” and select “Processor State”. Allow the solution temperatures to stabilize.

Note

Approximately 30 minutes may be needed for the PROCESSOR to warm up.

[2] Check that:

• DEVELOPER temperature remains at setpoint.

• FIXER temperature remains at setpoint or above.

• DRYER temperature remains at setpoint.

[3] Install:

• all PANELS

• EVAPORATION COVERS

• WET SECTION COVER

Note

Use 2 No. 10-32 SCREWS, 2 LOCK WASHERS, and 2 WASHERS provided in the PREPACK POLYBAG for
installation of the FEED END PANEL.

[4] On the 180 LPS PROCESSOR only, install the FILM TRAY and BIN.

H104_0072BA

EVAPORATION COVERS

CROSSOVERS

H104_0072BCA

Summary of Contents for Kodak X-Omat 180 LP











































Search results

Summary of Contents for Kodak X-Omat 180 LP

Reviews:

Related manuals for Kodak X-Omat 180 LP

Brands by name

Popular brands

EASTMAN Kodak X-Omat 180 LP, Installation Instructions Manual

Search results

Summary of Contents for Kodak X-Omat 180 LP

Reviews:

Related manuals for Kodak X-Omat 180 LP

Brands by name

Popular brands