background image

Catalogue

1.

Fault code list

------------------------------------------------------------ 3-4

2.

List of tools to use

------------------------------------------------------------ 5

3.

Cloak replacement -

------------------------------------------------------------6

4.

Replacement of flannelette in backrest

----------------------------------------- 7

5.

Movement disassembly

-1 ----------------------------------------------------- 8

6.

Movement replacement

-2 --------------------------------------------------- -9

7.

Movement replacement

-3 --------------------------------------------------- 10

8.

Remove the back cover

--------------------------------------------------------11

9.

Replacement of upper cover of central box

--------------------------------------12

10.

Remove side plate

----------------------------------------------------------- 13

11.

calves replacement-

---------------------------------------------------------- 14

12.

Movement backrest bus disassembly

-1 ------------------------------------- 15

13.

Movement backrest bus disassembly

-2------------------------------------- 16

14.

Movement backrest bus disassembly

-3---------------------------------------- 17

15.

Gas pump replacement

------------------------------------------------------- 18

16.

centre plate

transformer

Fuse replacement

---------------------------------- 19

2

Summary of Contents for EI-8602A-TIT





















Reviews: