EarthLinked TXV Kit Installation Manual Download Page 17 | Manualshive

Page: 17 / 28

background image

TXV–CLP-KIT (07/15)

Page 17

Step 5:

Measure and cut copper tubing to connect the liquid line from the TXV control box to the

liquid line stub out on the air handler as shown in Figures 3 and 9. Run the other liquid line from
the connection on the TXV control box to the compressor unit, also shown in Figures 3 and 9.
Nitrogen braze the joints.

Step 6:

Connect the pressure equalizer tube to the Schrader valve. Do not install the core. Tighten

the flare connection firmly.

Wrap the liquid and vapor tubing including the liquid line tubing to

the TXV control box, with Armaflex

®

, Insul-Tube

®

or equivalent insulation of at least ½” wall

thickness, between the air handler and compressor unit.

Figure 9. TXV Liquid Line Connections

«
...
15
16
17
18
19
...
»

Summary of Contents for TXV Kit





























Reviews:

No comments

Related manuals for TXV Kit

Brand: Danfoss Pages: 2

ENDURO 145 COMPRESSOR

Brand: Lavor Pages: 8

Brand: Zionair Pages: 16

PAC016002-3.3/100

Brand: P.I.T. Pages: 26

Brand: Emerson Pages: 23

Copeland Scroll ZB114 TFD

Brand: Emerson Pages: 70

Brand: Ingersoll-Rand Pages: 48

Brand: SereneLife Pages: 5

Brand: Rolls Pages: 2

Brand: WilTec Pages: 9

Brand: RIDGID Pages: 60

Brand: Sound Skulptor Pages: 7

Brand: Parkside Pages: 76

Delta 2 220/380V

Brand: METZGER Technik Pages: 12

Brand: JBM Pages: 24

ELECTRA-SAVER EAQ99Q

Brand: Gardner Denver Pages: 76

Brand: Campbell Hausfeld Pages: 44

Brand: Campbell Hausfeld Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands