manualshive.com logo in svg

EAE DA110, Product Manual, Page: 22 / 22

Share
Download
EAE DA110 Product Manual Download Page 22

Product Manual DA110 

EAE KNX DALI Gateway 

  

       

DA110 R2.0 

©

EAE Technology  

 

 

www.eaetechnology.com  

 

 

Page 21 / 21 

3.5. Scenes 

DA110 KNX-DALI Gateway can store 16 different lighting scenes. All of 16 scenes can be recalled only via “Scene 
8 bit” object. A maximum of 16 scenes can be recalled and store via “0=Scene x, 1=Scene y” 1 bit communication 
object as well.  

Activate scenes 1…16 

 

*no 

   yes 

Scene count can be selected in this page. This page only activates the DALI device control objects. Unselected 

device adresses can still be controlled in scenes. 

 

 

All scenes are disabled as default and they can be enabled by selecting “enable” in Scenes tab. “Scene x” tab 
will be available after enabled. 

3.5.1. Scene 1…16 

Fade time 

*jump to, 

0,7s…90s

 

 

Fade time can be selected for related scene. 

Device 1…64 brightness value 

*no change 

  0% (0)…100% (255)

 

Select the brightness value of ballasts for related scene. 

Summary of Contents for DA110























Reviews:

No comments