EAE DA110 Product Manual Download Page 18 | Manualshive

Page: 18 / 22

EAE DA110 Product Manual Download Page 18

Product Manual DA110

EAE KNX DALI Gateway

DA110 R2.0

©

EAE Technology

www.eaetechnology.com

Page 17 / 21

3.2. Feedback

Enable “DALI line fault” object

enable

*

disable

Parameter enables “Fault gateway supply” object. This object is used for reporting DALI gateway supply fault.

Possible causes of the fault are no mains connection to gateway supply terminal, power supply malfunction

or short circuiting DALI line more than 100ms. Please check

2.2 Communication Object Descriptions

for

detailed object information.

Enable “Mains connection fault” object

enable

*

disable

Parameter enables “Fault mains connected” object. This object is used for reporting a misconnection of mains

to the DALI line.

Enable “Lamp fault” object

enable

*disable

Parameter enables “Fault lamp” object. This object is used for reporting whether there is any device that has
a fault lamp is present or not.

Enable “Device fault” object

enable

*disable

Parameter enables “Fault ballast” object. This object is used for reporting whether there is any offline or
malfunctioned ballast/driver is present or not.

Enable “Device status” object

enable

*disable

Parameter enables “Device status” object. This communication object is used for getting all current faults and
states of a DALI device in one comprehensive telegram.

Enable “Coded status switch” object

enable

*disable

Parameter enables “Coded status switch” object. This object is used to get switch status of a DALI group or an
individual DALI ballast/driver.

Enable “Coded status brightness value” object

enable

*disable

Parameter enables “Coded status brightness” object. This object is used to get brightness value of a DALI
group or an individual DALI ballast/driver.

Enable “Coded faults” object

enable

*disable

Parameter enables “Coded faults” object. This object is used to get fault data of a DALI group or an individual
DALI device.

«
...
16
17
18
19
20
...
»

Summary of Contents for DA110























Reviews:

No comments