background image

warning signals

2S

BEx

EUROPEAN SAFETY SYSTEMS LTD

IMPRESS HOUSE

MANSELL ROAD

ACTON

LONDON W3 7QH

WWW.E2S.COM

C

THIS DRAWING AND ANY INFORMATION OR DESCRIPTIVE 

MATTER THEREIN IS COMMUNICATED IN CONFIDENCE AND 

IS THE COPYRIGHT PROPERTY OF EUROPEAN SAFETY 

SYSTEMS LTD. NEITHER THE WHOLE OR ANY EXTRACT MAY 

BE DISCLOSED, LOANED, COPIED OR USED FOR 

MANUFACTURING OR TENDERING PURPOSES WITHOUT THEIR 

WRITTEN CONSENT.

EUROPEAN SAFETY SYSTEMS LTD.

AS PER LATEST DATE OF ISSUE SHOWN ABOVE

DRAWING TO BS8888:2000

GEOMETRIC TOLERANCES TO ISO1101:1983

LINEAR DIMENSIONAL TOLS

ANGULAR DIMENSIONAL TOLS

STANDARDS

MOD No.

REASON - INITIAL - DATE

ISSUE

DATE

APPROVED

CHECKED

DATE

DATE

DRAWN

WEIGHT (Kg)

SURFACE FINISH

MATERIAL

ALTERNATIVE MATERIAL

SHEET

SCALE

TITLE

A3

IF IN DOUBT, ASK - 

DO NOT SCALE

ALL DIMENSIONS IN MM

DRAWING NUMBER

A

B

C

D

E

F

G

10

9

G

F

E

7

8

6

5

D

C

1

3

4

2

A

B

D210-06-601

R.S.RAIT

B.ISARD

R.N.POTTS

OF

NTS

1

1

OPTIONAL LINE MONITORING RESISTOR, CUSTOMER SUPPLIED,  

 500Ω MIN, 2W MIN OR 3K3Ω MIN, 0.5W MIN

MINIMUM VALUES:

R1

Single Stage Configuration

                         Config.: 1a

Line Monitoring

Set to negative switching (default)

Stage 1: Apply Power to Stage 1 +ve & Stage 1 -ve

Two Stage Configuration

             Config.: 1b

Common Positive

Set to negative switching (default)

Stage 1:Apply Power to +ve & -ve

Stage 2: Apply Power to +ve & -ve, Connect Stage 2 to -ve

Stage 3: Apply Power to +ve & -ve, Connect Stage 3 to -ve

Three Stage Configuration

      Config.: 1c

Common Negative

Set to positive switching (Customer to set header pin)

Stage 1:Apply Power to +ve & -ve

Stage 2: Apply Power to +ve & -ve, Connect Stage 2 to +ve

Stage 3: Apply Power to +ve & -ve, Connect Stage 3 to +ve

08/03/2022

08/03/2022

08/03/2022

BExCS110-05D DC COMBINED SOUNDER

& BEACON WIRING DIAGRAMS

INTRODUCTION

INTRODUCTION

1

RSR - 05/09/2022

Stage 1 -ve

Stage 1 +ve

Stage 2

-ve

+ve

Stage 3

Set to Positive Switching

R1

R1

Stage 2

+ve

-ve

Stage 3

R1

SWITCHES FOR STAGE OPERATION

CUSTOMER SUPPLIED

Stage 1 -ve in

Stage 1 +ve in

Stage 1 +ve out

Stage 1 -ve out

Stage 1 -ve in

Stage 1 +ve in

Stage 1 +ve out

Stage 1 -ve out

Stage 1 -ve in

Stage 1 +ve in

Stage 1 +ve out

Stage 1 -ve out

WIRING LINKING BEACON & 

SOUNDER FACTORY FITTED

Summary of Contents for BExCS110-05

















Reviews: