E2S 1-21-141 Instruction Manual Download Page 1

Page: 1 / 12

INSTRUCTION MANUAL

BExCBGL2-05D-P
Combined Beacon/ Beacon

ATEx/IECEx & UKEx Gas & Dust

European Safety Systems Ltd.

Impress House, Mansell Road, Acton, London W3 7QH

www.e2s.com

Tel: +44 (0)208 743 8880

Document No. D210-00-711-IS

Issue 6

12-09-2022

Sheet 1 of 6

BExCBGL2-05D-P

1. Product Table

Unit Type Code

Nominal

Input

Voltage

Chamber

Beacon

Nominal

Input Current

Cover Beacon

Nominal

Input Current

Max I/P Voltage

BExCBGL2-05DPDC024

24Vdc

240mA

300mA

28V

BExCBGL2-05DPDC048

48Vdc

130mA

180mA

54V

BExCBGL2-05DPAC115

115Vac

85mA

140mA

126V

BExCBGL2-05DPAC230

230Vac

48mA

55mA

253V

The table shows the input current taken by the various units.
Nominal current at nominal voltage.

Table 1: Electrical Ratings.

It is important that a suitable power supply is used to run the equipment. The power supply selected must have the necessary capacity
to provide the input current to all of the units.

The above table shows the input current taken by the various units and shows the maximum voltage at which they can be operated:

The input current will vary according to the voltage input level an flash rates selected.

2. Warnings



DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE IS PRESENT



DO NOT OPEN WHEN ENERGIZED



POTENTIAL ELECTROSTATIC CHARGING HAZARD – CLEAN ONLY WITH A DAMP CLOTH



COVER BOLTS CLASS A4-80



USE HEAT RESISTING CABLES AND CABLE GLANDS (RATED 110°C) AT AMB. TEMPERATURES OVER

40°C

Summary of Contents for 1-21-141













Search results

Summary of Contents for 1-21-141

Reviews:

Related manuals for 1-21-141

Brands by name

Popular brands

E2S 1-21-141, Instruction Manual

Search results

Summary of Contents for 1-21-141

Reviews:

Related manuals for 1-21-141

Brands by name

Popular brands