E-T-A ControlPlex CPC20, User Manual

Page: 23 / 32

23
9.1.2 »Configuration« configuration data of CPC20 Controller
The device configuration data for the controller consists of 17 bytes.
They will be read and written with COM = 0, channel = 0 and Index 3.
All parameters with possible conditions are described in the following table.
byte type range description
Configuration data
CPC 0 byte 0xFF bit 0 = writing via USB or web server. Allows changing of parame-
ters via the interfaces even when the bus connection is active.
Bit 1
TRUE: In the event of a bus interruption, the status of the load
outputs is maintained.
FALSE: In the event a bus interruption, all load outputs will be set
to the status OFF.
bit 2 saving mode, the LEDs will be dimmed for power reduction.
bit 3 = reserve
bit 4 = reserve
bit 5 = reserve
bit 6 = reserve
bit 7 = reserve
If not described otherwise, »True« means that the function is
active.
Control commands
lock EL-Bus 1 on
CPC channel 1 ... 16 1 HighByte
2 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 1; bit1 = channel 2 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 1
on CPC channel 17
... 32 3 HighByte
4 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 17; bit1 = channel 18 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 2 ex-
tension.
channel 1 ... 16 5 HighByte
6 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 1; bit1 = channel 2 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 2 ex-
tension.
channel 17 ... 32 7 HighByte
8 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 17; bit1 = channel 18 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 3 ex-
tension.
channel 1 ... 16
reserve 9 HighByte
10 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 1; bit1 = channel 2 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 3 ex-
tension.
channel 17 ... 32
reserve 11 HighByte
12 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 17; bit1 = channel 18 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 4 ex-
tension channel 1 ...
16 reserve 13 HighByte
14 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 1; bit1 = channel 2 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
Control commands
lock EL-Bus 4 ex-
tension channel 17
... 32 reserve 15 HighByte
16 LowByte Word 0xFFFF Each bit represents a channel.
(bit 0 = channel 1; bit1 = channel 2 ...)
If the bit is set, this means that the channel is not
switched on or off via the control unit or the web server.
fig. 26: Configuration data CPC