E-ride Industries 2013 Owner'S Manual Download Page 77 | Manualshive

Page: 77 / 102

background image

e-ride Industries

Page 75

9.1.3

Auxiliary Cab Heater (120 volt AC)

This heater is designed to preheat the cab and defog the windshield before driving the vehicle
without drawing power from the drive batteries. To operate the heater, plug in the car as if it
were being charged (see section

5.4.4 Charging Procedure

). The heater and charger share

the same plug, but a vehicle equipped with this option will have a label stating its presence.
When the power cord is plugged into the receptacle the charger will start up. The switch for
the heater is on the center console and labeled “PREHEAT”. This switch has three positions;
Off, On and Start. To start the heater, push on the top of the switch to rock it up to the on
position and then momentarily rock the switch all the way up to the start position and release.
After a few seconds, the heater will turn on and at the same time the charger will shut off.
The power supply plugged into the receptacle must be unplugged before the vehicle is turned
on or driven and will not do so otherwise (see section

5.4.6 Anti-Drive

for details about this

function). If the power is disconnected from the receptacle and then reconnected, the heater
will be off and the charger will be on. The heater switch must be restarted in order for the
heater to turn back on. This heater has an amp draw of 15 amps at 120 volts.

«
...
75
76
77
78
79
...
»

Summary of Contents for 2013







































































































Reviews:

No comments

Related manuals for 2013

Brand: Suzuki Pages: 16

Brand: Kargo Master Pages: 6

Brand: Condor Pages: 2

Brand: Parkeon Pages: 43

PRIME DESIGN VBI-FT21B

Brand: Safe Fleet Pages: 12

Plusone Console 4521011B

Brand: Honda Pages: 4

Brand: Belkin Pages: 2

THERAPEDIC 2000

Brand: Columbia Pages: 14

Brand: Rugged Ridge Pages: 2

FABIA II TMB PS 035

Brand: Skoda Pages: 16

Brand: Whispbar Pages: 14

Filtercharger 57-9004

Brand: K&N Engineering Pages: 4

Brand: Honda Pages: 219

Hitch-Haul 30110315

Brand: Masterbuilt Pages: 2

Brand: Mazda Pages: 605

BLADE-AL-HK4-EN

Brand: iDataLink Pages: 35

Countryman Cooper S

Brand: Mini Pages: 244

Brand: Edelbrock Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands