E.F. Johnson Company 53SL ES Series Operating Manual Download Page 26 | Manualshive

Page: 26 / 190

background image

1-4

53SL ES Series Mobile Radio Operating Manual April 2009

Available Options

Section 1 - Radio Overview

1.4

Available Options

Many features are optional and therefore may not be available in your specific radio
model. Availability of optional features is controlled by factory programming of the
control logic. Only those features that are specifically ordered and enabled in a particular
radio are available for use and can be programmed. The features controlled by factory
programming are as follows:

P25 Options

• P25 conventional mobile data
• P25 trunked mobile data
• P25 conventional operation
• P25 trunked operation

Encryption Options

• DES
• DES-OFB

OTAR Options

• OTAR P25 conventional
• OTAR P25 trunked

Trunking Options

• SMARTNET analog operation
• SmartZone analog operation
• Digital SMARTNET/SmartZone
• EFJohnson Multi-Net

Feature Options

• Keypad programming (Federal Government users only)
• Full Keypad support
• 512 or 864 talkgroups, depending on the option enabled
• Custom icons
• Zonefail site lock
• MDC1200
• 700 MHz Band
• Conventional Vote Scan

«
...
24
25
26
27
28
...
»

Summary of Contents for 53SL ES Series































































































































































































Reviews:

No comments

Related manuals for 53SL ES Series

Brand: Hama Pages: 24

Brand: Hama Pages: 4

Brand: Saab Pages: 4

7-Channel Weatheradio

Brand: Radio Shack Pages: 48

Brand: Grundig Pages: 8

E TRAVELLER VII

Brand: Grundig Pages: 9

Brand: Baofeng Pages: 25

Brand: AnyTone Pages: 32

Brand: Maxon Pages: 9

Brand: nanoradar Pages: 22

Brand: Yaesu Pages: 88

Brand: Kirisun Pages: 4

Brand: capello Pages: 28

Brand: jWIN Pages: 6

SOUND SOOTHER SI735

Brand: Sharper Image Pages: 18

Brand: Radioddity Pages: 24

Brand: Adeunis RF Pages: 40

Brand: August international Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands