manualshive.com logo in svg

E+E Elektronik EE772, User Manual

Share
Download
E+E Elektronik EE772 User Manual Download Page 9

9

3.4.  Required Length of Straight Pipe

The flow sensor should be installed as far as possible from disturbances of the flow. The causes for distur-

bance of the flow are for instance, reducers, elbows, T-pieces, valves, gate valves, etc. The specified meas-

urement accuracy can be achieved only when the following straight inlet and outlet pipe lengths are installed:

• 

The wall thickness of the inlet and outlet pipe should be 2.6 mm

• 

The stated values are as a minimum. If possible, allow for greater distances.

• 

Valves or gate valves should be installed downstream of the flow sensor.

• 

With lighter gases the inlet straight pipe should be longer.

Type

(DN = Nominal Pipe Size)

Straight inlet pipe Straight outlet pipe

Extension

15 x DN

5 x DN

Reduction

15 x DN

5 x DN

90° - elbow

20 x DN

5 x DN

Two 90° - elbows,  

in one level

25 x DN

5 x DN

Two 90° - elbows,  

in two levels, T-piece

30 x DN

5 x DN

Valve, gate valve

50 x DN

5 x DN

flow direction

straight inlet pipe

nominal pipe size (DN)

straight outlet pipe

Summary of Contents for EE772

































Reviews:

No comments

Brands by name

Popular brands

Load more brands