Dynojet 24xLC2 Linx Installation Manual Download | Manualshive

Page: 63 / 68

background image

A-1

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

A

P P E N D I X

A

R

ED

H

EAD

A

NCHOR

I

NSTALLATION

This appendix contains instructions for installing the Red Head Multi-Set™II
Anchors. The anchors will be used to secure the dyno to concrete. To ensure safety and
accuracy in the procedures, perform the procedures as they are described. Be sure to
read and understand the warnings included in this appendix.

WARNINGS

Always wear safety glasses and other necessary protective devices or
apparel when installing or working with anchors.

ITW Ramset/Red Head Multi-Set II Anchors are designed to operate
properly only when installed with ITW Ramset/Red Head brand Setting
Tools.

The use of a 24 to 40 ounce hammer is recommended for expanding Multi-Set II
anchors.

The use of carbide drill bits manufactured with ANSI B94. 12-77 drill bit diameter
requirements is recommended for installation of this anchor.

Not recommended for use in lightweight masonry material such as block or brick.

Use of core drills is not recommended to drill holes for use with this anchor.

Not recommended for use in new concrete which has not had sufficient time to cure.

Anchor spacing and edge distance requirements (anchor installation locations) are the
responsibility of the engineer of record.

CONTACT INFORMATION FOR ITW RAMSET/RED HEAD

Contact ITW Ramset/Red Head at 1-630-350-0370, or 1300 North Michael Drive,



Wood Dale, IL 60191.

«
...
61
62
63
64
65
...
»

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Related manuals for 24xLC2 Linx

Brand: Vega Pages: 68

Brand: Waycon Pages: 8

Brand: Cadillac Pages: 3

Brand: Cadillac Pages: 12

Brand: Cadillac Pages: 106

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 326

Brand: Cadillac Pages: 28

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 602

ESCALADE ESV 2004

Brand: Cadillac Pages: 20

ESCALADE EXT 2005

Brand: Cadillac Pages: 460

CT6 SUPER CRUISE 2018

Brand: Cadillac Pages: 8

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 337

TENSIONED CONTOUR ELECTROL

Brand: Da-Lite Pages: 8

Brand: Dacor Pages: 4

Brand: Eclipse Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands