manualshive.com logo in svg

Dynojet 24xLC2 Linx, Installation Manual

Share
Download
Dynojet 24xLC2 Linx Installation Manual Download Page 41

     

37

L I N X   W I T H   A T R A   F L E X   I N S T A L L A T I O N

Upper Pulley Mount Installation

Version 3

Linx with Atra Flex Installation for Model 424 Automotive Dynamometers

I

NSTALLING

 

THE

 U

PPER

 S

TATIONARY

 D

YNO

 P

ULLEY

 M

OUNT

1

Place the upper stationary dyno pulley mount (P/N 61300022, stamped 1) over 
the stationary dyno pulley and loosely secure the mount to the inner plate using 

five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers (one of the holes on the 
pulley mount is not used).

2

Loosely secure the pulley mount to the stationary dyno pulley bearing plate using 
five 3/8-16 x 1-inch bolts and five 3/8-inch flat washers.

3

While applying upward pressure to support the shaft and pulley, tighten all the 
bolts.

4

Using the installation instructions in 

Appendix B

, secure the cap screws.

Figure 30: Install the Pulley Mount Over the Stationary Dyno Pulley

pulley mount

P/N 61300022

stamped 1

Summary of Contents for 24xLC2 Linx





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands