Dynamic DS120 Installation Manual Download Page 88 | Manualshive

Page: 88 / 128

Dynamic DS120 Installation Manual Download Page 88

Chapter 4: Programming the Rhino2

88

Notes:

This test procedure causes the motor to become hot. For this reason, the resulting
value for

Load Compensation

is too high. Reduce

Load Compensation

by 20% to

make sure that the scooter is still comfortable to drive when the motor is cold.

A new motor usually has a higher motor resistance than a motor that has been used
for some time, because the motor brushes that are inside the motor do not make
optimal contact until they are "worn in". If possible, perform this procedure when the
motor has been used for several hours.

4.4.5.6

Maximum Load Compensation

Parameter

Possible Values

Default

HHP

Lite

Std Adv

Maximum Load Compensation

0 - 225 mΩ

DS90, DS120:

200mΩ

DS160:

100mΩ



This parameter sets the maximum value that the

Load Compensation

parameter can be set to.

This value must be set by the OEM to match the motors of the scooter.

Maximum Load Compensation

prevents the dealer from setting

Load Compensation

to a

value that is too high, which can be dangerous.

4.4.5.7

Load Compensation Damping

Parameter

Possible Values Default

HHP

Lite

Std

Adv

Load
Compensation
Damping

15 - 60%

50%



Load Compensation Damping

is used to dampen the effects of the load compensation to

avoid bucking and instability at high

Load Compensation

settings.

The recommended value for this parameter is between 25 – 50%. It‟s important to avoid
higher values of

Load Compensation Damping

as this can lead to the load compensation

continuing to be applied when the motor current has fallen, causing problems such as the
scooter continuing to surge forward after, for example, climbing an obstacle.

The

Load Compensation Damping

parameter interacts with the following parameters:

Remembered Load Compensation

Load Compensation

Park Brake Neutral Delay

When setting these parameters, follow the method below:

1.

Adjust the

Load Compensation

parameter first to give correct driving performance.

2.

Adjust

Load Compensation Damping

to minimise bucking, while keeping the system

responsive.

3.

Adjust the

Park Brake Neutral Delay

parameter to provide acceptable rollback on

slopes and prevent jerking – higher values decrease jerking but give more rollback
and vice versa.

4.

Adjust the

Remembered Load Compensation

to give acceptable starting

performance when the park brakes are released, both when driving on the flat and
on slopes. (Note: this parameter has no effect if the scooter stops and restarts driving
quickly such that the park brakes are never applied.)

«
...
86
87
88
89
90
...
»

Summary of Contents for DS120

































































































































Reviews:

No comments