background image

1

VENT-FREE

BLUE FLAME

GAS WALL HEATER

MODEL #BF10DTDG-1

BF20DTDG-1
BF30DTDG-1 

GBF30DTDG-1

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING: 

IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED 

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY 

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

       WARNING:

 This appliance is equipped for 

Natural and Propane gas. Field conversion is not 

permitted.

- Do not store or use gasoline or other flammable vapors and Iiquids in vicinity of this or 

  any other appliance.
  WHAT TO DO IF YOU SMELL GAS
  • Do not try to light any appliance.

  • Do not touch any electrical switch; do not use any phone in your building.

  • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s  

    instructions.

  • If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the 

   gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is 

installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Air For Combustion and Ventilation section on page 8 of this manual.

This appliance may be installed in an aftermarket, permanently located, manufactured (mobile) 

home, where not prohibited by local codes. 

This appliance is only for use with propane or natural gas. 

This appliance is equipped with a simple means to switch between propane and natural gas. 

Field conversion by any other means including the use of a kit is not permitted.

C           US

       WARNING

: Do not attempt to access or 

change the setting of the fuel selection means.
Access to and adjustment of the fuel selection 
means must only be performed by a qualified 

service person when connecting this appliance to a 

specified fuel supply at the time of installation.
Change of the selector setting to other than the fuel 

type specified at the time of installation could dam-

age this appliance and render it inoperable.
The installer shall replace the access cover before 

completing the installation and operating this appli-

ance.

C           US

ANS Z21.11.2-2013

IMDFBF - 2015-06-04

Gas Fired Room Heaters

Volume II - Unvented Room Heaters

Questions, problems, missing parts?

 Before returning to your retailer, call our customer 

service department at 1-877-447-4768,

 

8:30 a.m. –  4:30

 

p.m., CST, Monday – Friday or 

email us at [email protected].

Summary of Contents for BF10DTDG-1































Reviews: