background image

- 1 -

INSTALLATION INSTRUCTIONS

SA

VE FOR FUTURE USE

M965530 Rev. 1.3

ROUGHING-IN DIMENSIONS: 

• For reference

Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2013

In the United States:

DXV by American Standard
One Centennial Avenue 
Piscataway, New Jersey 08855
Attention: Director of Customer Care

For residents of the United States, warranty 
information may also be obtained by calling 
the following toll free number: (800) 227-2734
www.DXV.com

In Canada:

DXV by American Standard
5900 Avebury Road  
Mississauga, Ontario 
L5R 3M3
Canada

Toll Free: 1-800-387-0369
Local: 905-306-1093

Fax: 1

-800-395-1498

www.DXV.ca

In Mexico:

DXV by American Standard
Via Morelos 330
Col. Santa Clara Coatitla 
Ecatepec, Estado de México 55540

Toll Free: 01-800-8391200
www.DXV.mx

Percy

™ 

Single Control Lavatory

and Vessel Faucet

Loop Handle Vessel - Model D35105154

Pixie Handle Vessel - Model D35105150

Loop Handle Lavatory - Model D35105104

Pixie Handle Lavatory - Model D35105100

Adjustable Wrench

 Flat Blade Screwdriver

Channel Locks

NOTE: MOUNTING HOLE

1-1/4" (32mm) D.

MOUNTING

SURFACE

20"

(508mm)

FLEXIBLE

HOSES

9-9/16"

(243mm)

6-3/4"

(171mm)

8-13/16"

(223mm)

3-5/8"

(92mm)

1-1/2"

(38mm) MAX.

2-1/4"

(57mm)

1-1/4" OD

(32mm OD)

4-1/2"

(114mm)

1-13/16"

(46mm) D.

1-11/16"

(43mm) D.

2-7/16"

(63mm) D.

LOOP

HANDLE

PIXIE

HANDLE

14-7/8"

(378mm)

14-1/8"

(359mm)

4-1/4"

(108mm)

3-3/4"

(95mm)

3"

(76mm)

6-3/4"

(171mm)

8-15/16"

(227mm)

2-1/4"

(57mm)

4-1/2"

(114mm)

9-5/8"

(244mm)

SUPPLY CONNECTIONS

ARE 3/8" COMPRESSION

     2"

(51mm) MAX.

RECOMMENDED TOOLS AND MATERIALS

Thank you for selecting DXV by American Standard.
To ensure that your installation proceeds smoothly,
please read these instructions carefully
before you begin.

Most of the procedures require the use of common tools and materials, which are available from hardware and plumbing, 

supply stores. It is essential that the tools and materials be on hand before work is begun.

Summary of Contents for Percy D35105100









Reviews: