A quality 100% clear silicon sealer.
Plumbing tailpiece designed for sinks without overflows.
Soft cotton rag.
Pencil
Tape Measure
Installation Guide:
Drop In Installation:
Since your D’Vontz copper sink is manufactured by hand, we are unable to provide a
template due to variations that occur in width and length. Please proceed as follows:
Measure width across top of sink from outside edge to outside edge. Approximate width
will be 17”. Determine countertop hole size by subtracting 1” from this dimension. Layout
this dimension on countertop and cut hole.
Once countertop hole is cut, set sink inside hole and center. Trace outside rim of sink
lightly with a pencil. Remove sink and apply a 3/8” bead of silicon sealant around hole
centered on the pencil line.
Before setting sink in countertop, prepare and attach drain to sink. We
recommend clear silicone sealant under tailpiece flange. See Figure B. After tightening
drain, remove excess putty or sealer. Allow silicone to dry before removal.
Carefully set sink into countertop hole and sealant. Once positioned, carefully remove
excess sealant from the outside rim of sink with a soft cotton rag while holding downward
pressure on sink.
Sink must set a minimum of 12 hours for sealer to set before putting any movement or
pressure on sink.
Under Mount Installation for Flat Edged Sink:
Measure inside diameter of sink. Subtract one inch from this dimension to obtain
dimension of countertop opening.
NOTE: During the installation of this product, the only sealant or adhesive that is Manufacturer Approved is a
100% Silicone based product. Failure to use Kitchen and Bath 100% Silicone based products will VOID ALL
manufacturer warranties and manufacturer finish warranties. Specifically, the use of Plumbers Putty is
EXPRESSLY PROHIBITED and will VOID ALL manufacturer warranties and manufacturer finish warranties.
Thank You for choosing our D’Vontz Copper Sink
We appreciate your choice of our product. All the information in this guide is based
upon the latest product information available at the time of publication. We reserve the
right to make changes in product specifications at any time without notice. Please take a
few moments to review this guide, if you have any questions please contact us at 877-322-3600.
Items needed for Installation:
INSTALLATION GUIDE
Exclusively Designed
• INTERNATIONALLY RECOGNIZED
Copper Sink
•
Center sink on opening and adhere sink to underneath surface of countertop with silicone
adhesive or other suitable adhesive applied to sink flange. Support sink until adhesive
cures.
Vessel Installation:
Additional items needed for Vessel installation:
Drill Motor with a 2 ¾” and 1 5/8” Hole Saw.
24” Level.
•
Determine installation location on countertop for sink and mark centerline for drain hole.
•
Use a 2 ¾” hole saw and drill a hole using the centerline mark to a depth of 3/8”.
•
Next drill a 1 5/8” diameter hole in the middle of the 2 ¾” hole that goes all the way
through the countertop. See Fig. A.
Fig. A
•
Remove material from the 2 ¾” cut to a depth of 3/8”. Test fit sink into recess.
•
Run a ¼” bead of silicone in 2 ¾” recess. Place sink into recess and level from side to side
and front to back. Install sink tailpiece through sink and countertop.
•
Silicone should be used under drain flange. See Figure B. After tightening drain, allow silicone
r
to dry and emove excess sealer. Connect drain trap and associated plumbing. Allow 12 hours for
silicone to dry before use.
1 5/8”
2 3/4”
Side View
3/8”
2 3/4”
1 5/8”
Overhead View
Fig. B
Fig. C
Care and Maintenance:
Caring for our copper bowls is surprisingly easy. Rinsing your sink with clean water and
drying with a soft cloth after each use will help keep your sink looking new. For cleaning
use a liquid dish soap and water with a non-abrasive sponge. Never use abrasive
cleaners. Most copper sinks are considered a “live” finish, meaning the patina (finish)
will
change over time. If you ordered the Dark Smoke finish, this patina will continue to
darken over time as you use your sink giving an “Old World” look.
Do not use copper
cleaners, abrasive materials or harsh chemicals on this sink as this will remove the
patina.
If a chemical lightens the finish, don’t worry, time will return the darker patina.
For maintaining the Shiny Copper finish, copper cleaners or lemon juice will restore it to
its original luster. For added protection, paste waxes such as Flitz Furniture and Faucet
Wax or any quality automotive wax will help maintain the beauty of your sink as well as
help keep it clean.
________________________________________________________________________
SEAL WITH SILICONE BETWEEN DRAIN
FLANGE & SINK DRAIN HOLE
RUBBER WASHER
METAL WASHER
SEAL WITH SILICONE BETWEEN DRAIN
FLANGE & SINK DRAIN HOLE
RUBBER WASHER
METAL WASHER
UNDERMOUNT
OR DROP-IN
INSTALLATION
VESSEL MOUNT
INSTALLATION
If you have any trouble during the installation of your D’Vontz sink, please call our Customer Service department at
877-322-3600.
Thank You for choosing D’Vontz.
Please install this product according to the installation guide and all local plumbing codes.
D’VONTZ • 7208 EAST 38th STREET • TULSA, OKLAHOMA 74145 • 918.622.3600 • FAX 918.622.3649 • WWW.DVONTZ.COM
LIMITED WARRANTY
−
Use of any cleaning products other than those suggested by D’Vontz will void warranty. See
care and installation instructions included with product or available
at www.dvontz.com
−
Use of “plu
m
ber’s pu y or abrasive cleaners
”
on any product will void all warranties!
−
All D’Vontz products are warranted to the original purchaser to be free of defects in material
and workmanship for one year from the purchase date.
−
This limited warranty only applies to the original purchaser of our product. Proof of Purchase
in the form of the original sales receipt will be required for any warranty claim.
−
This limited warranty does not cover any costs associated with a product’s removal and/or
reinstallation, including labor, materials or damage to surrounding products or goods.
−
There is no warranty on copper sink or tub patinas. Please refer to the care instructions
included with these products.
D’Vontz L.L.C. 7208 E. 38th St., Tulsa, Oklahoma 74145 877-322-3600 ph 918-622-3649 fax
−
There is no warranty on any living finishes, including Oil Rubbed Bronze, Victorian Bronze
and Venetian Bronze.
−
All faucet cartridges carry a limited lifetime warranty.
