manualshive.com logo in svg

Durr Dental 6024100001, Installation And Operating Instructions Manual

Share
Download
Durr Dental 6024100001 Installation And Operating Instructions Manual Download Page 26

Troubleshooting

17 Messages

17.1 "Caution" messages

After acknowledgement the unit will continue to work, but only with limited functions.

Message: Caution

No SD card present. Insert the SD card and restart the device.
SD card write error. Restart the device.
Pressing force too high. Please repeat the sealing process.
Pressing force too low. Please repeat the sealing process.
Sealing temperature too high. Please repeat the sealing process.
Sealing temperature too low. Please repeat the sealing process.
Light barrier triggered for too long.
Sealing speed too high. Please repeat the sealing process.
Sealing speed too low. Please repeat the sealing process.

17.2 "Fault" messages

The unit will no longer function.
When the error has been remedied, it may be necessary to acknowledge the error message.

Message: Fault

Power supply unit defective.
Device overheating. Please wait.
Temperature sensor defective.
Foil transport blocked.
Heating defective. Contact a Service Technician.
Pressing operation defective.
Motor current too high.

17.3 "Note" messages

Important information for the operator, e.g. about the current status of the device.
The unit continues to operate.

Message: Note

Restart device to apply language

Troubleshooting

24

6024100132L02 1906V003

EN

Summary of Contents for 6024100001





































Reviews:

No comments

Brands by name

Popular brands

Load more brands