DUROMAX DuroStar DS10000E Page 45 User Manual Download

Page: 45 / 80

Disconnecting battery

When disconnecting, always disconnect the wires from the

generator first to avoid a spark.

DANGER

: Stored batteries emit highly explosive hydrogen gas when charged.

Batteries also contain acid, which can cause severe chemical burns.

DANGER

: Do not allow open flames or cigarettes nearby for several minutes after

charging a battery.

DANGER

: Always wear protective goggles and rubber gloves when charging a

battery.

DANGER

: If battery acid gets on your skin, flush with water. If battery acid gets in

your eyes, flush with water and call a physician immediately.

DANGER

: If battery acid is swallowed, drink large quantities of milk and call a

Physician immediately.

CAUTION

: Never try to jump start a car with your generator.

CAUTION

: The DC receptacle is for recharging 12 Volt automotive-type batteries

only. Do not connect any other device to this receptacle.

Summary of Contents for DuroStar DS10000E

















































































Search results

Summary of Contents for DuroStar DS10000E

Reviews:

Related manuals for DuroStar DS10000E

Brands by name

Popular brands

DUROMAX DuroStar DS10000E, User Manual

Search results

Summary of Contents for DuroStar DS10000E

Reviews:

Related manuals for DuroStar DS10000E

Brands by name

Popular brands