manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 90

Maintenance work

88

Service manual H867 Version 00.0 - 08/2013

20.3 Checking the toothed belt

The condition of the toothed belt must be checked once a month.

A damaged toothed belt must be replaced immediately.

Correct setting

The toothed belt exhibits no cracks or fragile areas.

When pressed with a finger, the toothed belt gives no more than 10 mm.

Cover

• Tilt the upper section backwards 

(

 Section 

4.4.1 Access to the machine bottom section

, page 10)

Figure 73: Checking the toothed belt

Test steps

1. Check the toothed belt for cracks or fragile areas.

The toothed belt should be tight and undamaged.

2. Prod the toothed belt gently in the middle using your finger.

The toothed belt should give no more than 10 mm.

Risk of injury

Switch off the machine at the main power switch before check-
ing the condition of the toothed belt.

WARNING

1

(1) - Toothed belt

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands