manualshive.com logo in svg

Dürkopp Adler M-TYPE H867, Service Manual

Share
Download
Dürkopp Adler M-TYPE H867 Service Manual Download Page 17

Working basis

Service manual H867 Version 00.0 - 08/2013

15

4.4.7 Removing and inserting the feed-dog

Figure 7: Removing and inserting the feed-dog

Removing the feed-dog

1. Remove the throat plate.

(

 Section 

4.4.6 Removing and inserting the throat plate

, page 14)

2. Loosen the feed-dog screws (3).

3. Take the feed-dog (1) off the feed-dog carrier (2).

Inserting the feed-dog

1. Place the feed-dog (1) onto the feed-dog carrier (2).

2. Screw the feed-dog screws (3) firmly in place.

3. Insert the throat plate.

(

 Section 

4.4.6 Removing and inserting the throat plate

, page 14)

Important

: Check the feed-dog position in its movement by turning the 

handwheel. The feed-dog must not hit against the throat 
plate.

Risk of injury

Switch the sewing machine off before you remove or insert the 
feed-dog.

WARNING

2

3

1

(1) - Feed-dog
(2) - Feed-dog carrier

(3) - Feed-dog screws

Summary of Contents for M-TYPE H867





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands