Duratax NITRO DEMON Assembly And Operation Manual Download Page 1

Warranty

• DuraTrax

®

will warranty this kit for 90 days after the purchase date from defects in materials or workmanship. DuraTrax

will either repair or replace, at no charge, the incorrectly made part.

• Make sure you 

save the receipt or invoice

you were given when you bought your model! It is your proof of purchase

and we must see it before we can honor the warranty.

• To return your Nitro Demon for repairs covered under warranty you should send your truck to:

Hobby Services

1610 Interstate Drive

Champaign, Illinois 61822

Attn: Service Department

Phone: (217) 398-0007 9:00 am - 5:00 pm Central Time M-F

E-mail: 

[email protected]

Before Building:

We want the building and operating of this vehicle to be a success, so 

BEFORE

removing any parts from the parts bags

please read this manual thoroughly and watch the included video to familiarize yourself with the model. If for any reason
you think this model is not for you, return it to your dealer immediately. 

PLEASE NOTE: 

Your hobby dealer cannot accept

a return on any model after assembly has begun.

© Copyright 2000

DTXZ1081 For Kit DTXC0075/DTXD75**

ASSEMBLY AND OPERATION MANUAL

®

Summary of Contents for NITRO DEMON





















Reviews: