Duplo DF-990 Instruction Manual Download

Page: 9 / 100

Chapter 1 Before Operation

2-3. Installation procedures

Open the side cover.

Remove the tape fixing the lever.

Be sure to remove the tape fixing the lever.

If you use the machine without removing the

tape, the machine cannot detect the presence

of the folding plate 2.

Check that the folding stopper does not

protrude from the cover on the paper

feeding side of the folding plate 2.

When attaching the folding stopper to this

machine with the folding stopper protruding

from the cover, the folding stopper will touch

inside the machine. If so, rotate the gear in

the direction of an arrow to move the folding

stopper to the inner section of the cover.

Do not hold the belt section of the folding

plate 2. Doing so will result in malfunction

of the machine.

Hold the folding plate 2 as shown in the figure, and insert it into the machine.

Hold the areas that are indicated with the labels on the folding plate 2.

[A]

[B]

Insert the folding plate 2 with its rollers [A]

moving along the rails [B] of the machine.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands