Duplo DF-990 Instruction Manual Download Page 86

Page: 86 / 100

Chapter 5 Cleaning the Machine

Cleaning sensor

If the sensor is dirty, the detection function may not work properly.

Keep in mind the following notes when using the air duster.

•

Use a non-flammable air duster. Read the cautions for use well, and be sure to keep the

descriptions in mind.

• The sensors and metallic section are cooled by gas in the air duster, and may be temporarily

condensed. Wait for about five minutes.

Paper feed timing sensor (up and down), paper sensor, double-feed detection sensor (up and down)

[1]

[2]

[3]

Open the top cover.

Remove dust with an air duster.

[1] Paper feed timing sensor upper
[2] Paper sensor
[3] Double-feed detection sensor (up and down)
Ultrasonic sensor (up and down) (option)

Paper ejection jam sensor upper

Remove dust with an air duster.

Paper ejection jam sensor lower

Open the side cover.

Remove the folding plate 2.

Remove dust with an air duster or wipe

with a dry cloth.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Brands by name

Popular brands