manualshive.com logo in svg

Duplo DF-990, Instruction Manual

Share
Download
Duplo DF-990 Instruction Manual Download Page 82

78

Chapter 4 Using the DF HAND FEED KIT

Copyright © 2019 Duplo Corporation All Rights Reserved

4.  Operation

Do not put fingers inside during operation.

Keep away long hair, ties, jewelry and loose clothing.

It could cause injury.

1 

Open the paper receiving tray to 

the right side when it is seen on the 

operator’s side.

2 

Attach the auxiliary paper ejection 

guide to the stacker roller.

3 

Set [Manual Feed Mode].

 

 “3.  Manual Feed Mode Setting” (p.77)

When running thick sheets, set a speed 

to higher levels. Low speeds may cause 

abnormal folds.

4 

Set the paper to the hand feed paper 

feed guide of the hand feed paper feed 

tray.

Do not insert the paper into the inlet.  

Inserting paper into the inlet will result in 

paper jam or injury as the sensor detects 

and the paper is fed.

5 

Set the auxiliary guide to the paper side.

Set the auxiliary guide leaving some clearance between the guide and paper.  Too much 

pressure may cause a paper feed error such as mis-feed, etc.

Summary of Contents for DF-990





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands