Duplo DF-1200 Instruction Manual Download

Page: 26 / 98

1-14

Chapter1 Before Operation

6-2. Precautions on stacking paper

Paper feed tray

Paper

Striking

Shutter

paper

detecting

sensor

• Stack paper striking the leading edge of paper

lightly at the shutter.

If there is some clearance between the

leading edge of paper and shutter, the

paper detecting sensor does not function

properly.

• Do not stack the sheets of paper on the paper

feed tray with the sides of sheets unaligned or

some sheets protruding from the stack.

Processing with sheets unaligned on the

right or left side may cause such trouble as

folding misalignment and jamming.

• Do not stack paper on the paper feed tray with

the lead and trail edges unaligned or some

sheets protruding out.

Processing with sheets unaligned on the

lead and trail edges may lead to unstable

feed causing such trouble as mis-feed and

double-feed.

Summary of Contents for DF-1200



































































































Search results

Summary of Contents for DF-1200

Reviews:

Related manuals for DF-1200

Brands by name

Popular brands

Duplo DF-1200, Instruction Manual

Search results

Summary of Contents for DF-1200

Reviews:

Related manuals for DF-1200

Brands by name

Popular brands