Dunkirk DMG-380 Installation, Operation & Maintenance Manual Download Page 49

Page: 49 / 88

Display

[Escape] or RESET button

Heating Temperature or [-] button

DHW temperature or [+] button

[Enter] or cancel

lock-out button

Setup buttons (press the 2 and 3

buttons simultaneously)
[Menu] buttons (press the 4 and 5

buttons simultaneously)

ON/OFF switch

9 - START UP PROCEDURE

9.5 Control Panel

Symbols

Information menu:

Reading the various current values
Chimney-sweeping position: Forced full or part

load for CO2 measurement.
User menu: Parameters at user level can be

changed.
Heating program deactivated: The heating

function is deactivated.
Manual mode:

Boiler is set to manual operation.
DHW program deactivated:

DHW mode is deactivated.
Service menu: Parameters at installer level can be

changed.
Energy-saving mode: Economic mode activated.

Fault: Boiler fault indicated.

Can be seen from é code and red display.

Frost protection:

Boiler running in frost protection mode.
Hour counter menu: Readout of operating hours,

number of successful starts and hours on main supply.

ON/OFF switch: After 5 lock-outs, boiler must be

switched OFF/ON again.

Boiler pump: Pump operates

Heating system function: Access to heating system

temperature parameter.
DHW function: Access to potable hot water

temperature parameter.
Yellow display with symbols: + s

(Maintenance message).
Water pressure: Water pressure is too low.

Burner Level: Boiler is running at full or low load.

Locking keys: Key lock-out is activated.

https://image.freepik.com/free-icon/double-wrench-outline_318-44667.jpg[10/14/2016 11:44:32 AM]

PN 240011664, Rev. L [11/01/2020]

Summary of Contents for DMG-380

























































































Search results

Summary of Contents for DMG-380

Reviews:

Brands by name

Popular brands

Dunkirk DMG-380, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for DMG-380

Reviews:

Brands by name

Popular brands