A
B
C
D
E
F
G
H
L
M
N
P
Mototelaio
Frame
sezione / section
H 2
8
749R
- M.Y. 2006 - edizione/edition 00
Smontaggio componenti
cannotto di sterzo
Allentare la vite (5) che blocca la testa
di sterzo sulla ghiera (10).
Allentando la vite (5) si libera il
martelletto del bloccasterzo.
Segnare la posizione del martelletto
perchè al rimontaggio dovrà essere in
posizione originale.
Sfilare la testa di sterzo (11).
Con l'attrezzo cod.
88713.1058
allentare la ghiera (10) e svitarla dal
perno di sterzo.
Sfilare dal perno di sterzo l'anello di
tenuta (2), la pista interna (C) e la
corona di sfere (B) del cuscinetto (3)
superiore.
Per agevolare l’operazione, battere
il perno di sterzo per poi riuscire a
scalzare i componenti citati.
Rimuovere i seeger (
8
) e allentare
le viti (7).
Svitare e rimuovere la vite (9) che
definisce la posizione dell'angolo
di sterzo (Segnarsi la posizione per
riposizionarla durante il rimontaggio).
Sfilare dal tubo del telaio il cannotto (4)
con eccentrico (
13
), perno e base
di sterzo (1).
Supportare il cannotto (4) e con
mazzuolo battere sul perno per sfilarlo
unitamente alla base di sterzo.
Sfilare la corona di sfere (B) del
cuscinetto inferiore (3).
Sul perno rimarrà posizionata la pista
interna (C) del cuscinetto inferiore e il
relativo anello di tenuta (2).
Utilizzare un estrattore universale
(del tipo raffigurato) per rimuovere la
pista (C) dal perno di sterzo, facendo
molta attenzione a non rovinare la
sede.
Importante
Gli anelli di tenuta (2) e i
cuscinetti (3) rimossi non vanno più
rimontati.
Rimuovere gli anelli esterni dei
cuscinetti dal cannotto utilizzando un
punzone adeguato e facendo molta
attenzione a non rovinare le sedi.
Operazioni
Rif. Sez.
Rimuovere le carenature
laterali
E 2
Rimuovere il cupolino
E 1
Rimuovere gli steli
forcella
G 2
Rimuovere l'ammortiz-
zatore di sterzo
H 3
Removing the steering
head components
Loosen the bolt (5) securing the top
yoke to the ringnut (10).
Slackening off the bolt (5) frees the
steering lock peg.
Mark the position of the peg to
ensure that it is replaced in its original
position on reassembly.
Remove the top yoke (11).
With the service tool part
no.
88713.1058
loosen the ring
nut (10) and unscrew it from the
steering stem.
Remove the seal (2), inner ring (C)
and ball race (B) of the upper
bearing (3) from the steering stem.
To facilitate the operation, tap the
steering stem to dislodge the
components.
Remove the circlips (
8
) and slacken
off the bolts (7).
Unscrew and remove the bolt (9)
which sets the steering angle
(mark its position to refit it correctly
during reassembly).
Withdraw the steering tube (4) with
the eccentric tube (
13
), steering stem
and bottom yoke (1) from the frame
tube.
Support the steering tube (4) and use
a mallet to drive out the stem
together with the bottom yoke.
Remove the ball race (B) of the lower
bearing (3).
The inner race (C) of the lower
bearing and its seal ring (2) will remain
on the stem.
Using a universal puller (of the type
shown in the figure) remove the
ring (C) from the steering stem,
taking care not to damage the seat.
Important
Once removed, the seals (2)
and the bearings (3) must not be
refitted.
Using a suitable drift, remove the
outer bearing races from the steering
tube. Proceed with extreme care to
avoid damaging the seats.
Operation
See Sect.
Remove the side
fairings
E 2
Remove the headlight
shell
E 1
Remove the fork legs
G 2
Remove the steering
damper
H 3
11
10
5
9
7
88713.1058
10
2
C
B
4
4
B
C
3
2
1
14
Summary of Contents for Superbike 749R 2006
