A
B
C
D
E
F
G
H
L
M
N
P
Comandi – Dispositivi
Controls – Devices
sezione / section
F 3
17
749R
- M.Y. 2006 - edizione/edition 00
Attenzione
La casa costruttrice delle pinze e
delle pompe freno, considerando
l’importanza in termini di sicurezza
che rivestono questi componenti,
suggerisce di non intervenire in
nessun modo all’interno della pinza o
della pompa. Una revisione non
eseguita correttamente può mettere
in serio pericolo l’incolumità del pilota
e del passeggero.
Le operazioni di sostituzione si devono
limitare alla leva di comando, al gruppo
serbatoio con relativi componenti di
fissaggio e al fissaggio pompa.
Smontaggio pompa freno
idraulico anteriore
Svitare le viti (1) di fissaggio e
rimuovere il gruppo pompa freno
anteriore dal semimanubrio.
Per lo smontaggio e la sostituzione dei
componenti del gruppo pompa seguire
le indicazioni dell’esploso riportato a
inizio capitolo.
Quando si effettua il rimontaggio delle
tubazioni è necessario interporre i
raccordi con le guarnizioni (
4
) e serrare
la vite alla coppia prescritta (Sez. C 3).
Rimontaggio pompa
freno idraulico anteriore
Posizionare il perno di riferimento sul
corpo pompa nell’apposito foro (A)
ricavato sul semimanubrio.
Eseguire il serraggio alla coppia
prescritta (Sez. C 3) delle viti (1) con
sequenza 1-2-1, partendo sempre da
quella superiore.
Attenzione
Una tubazione mal posizionata
può causare un malfunzionamento
dell’impianto frenante e può
ostacolare le parti in movimento del
motociclo. Rispettare l’orientamento
rappresentato in figura.
Per la sostituzione delle tubazioni
freno anteriore fare riferimento alla
Sezione G 3.
Operazioni
Rif. Sez.
Svuotamento
dell’impianto frenante
D 4
Scollegare il tubo
comando freno dal
gruppo pompa
G 3
Operazioni
Rif. Sez.
Ricollegare il tubo
comando freno alla
pompa
G 3
Riempimento
dell’impianto frenante
D 4
Warning
The brake calliper and master
cylinder manufacturer advises against
servicing the internal components of
calliper and brake master cylinder,
in view of the safety-critical nature
of these parts. Incorrect overhaul of
this critical safety component can
endanger the rider and passenger.
Maintenance operations on these
units are limited to renewal of the
following parts: control lever, fluid
reservoir assembly and relative
fasteners and master cylinder
fasteners.
Removing the front brake
master cylinder
Unscrew the clamp bolts (1) and then
remove the front brake master
cylinder from the handlebar.
Refer to the exploded view at the
beginning of this section for
indications on disassembly and
replacement of the brake master
cylinder components.
When reconnecting the hoses, install
the hose end fittings with their
sealing washers (
4
) and tighten the
banjo bolt to the specified torque
(Sect. C 3).
Refitting the front brake
master cylinder
Locate the pin on the master cylinder
body in the hole (A) in the handlebar.
Tighten the bolts (1) to the specified
torque (Sect. C 3) in a 1-2-1
sequence, always starting with the
top screw.
Warning
An incorrectly positioned hose
can affect brake operation and foul
moving parts. Position the hose as
shown in the figure.
For renewal of the front brake hose,
refer to Section G 3.
Operation
See Sect.
Draining the brake
circuit
D 4
Disconnect the brake
hose from the master
cylinder unit
G 3
Operation
See Sect.
Reconnect the brake
hose to the master
cylinder
G 3
Filling the brake system
D 4
1
A
65˚±2
5
Summary of Contents for Superbike 749R 2006
