background image

4

XNBP SERIES

GUIDELINES

Enclosure Guidelines

We at Dual have provided placement recommendations and installation tips for your
enclosures.  These are a result of many hours of development and experimentation.
These examples are provided to you as a guide line. Please feel free to experiment
yourself as you may find that other placements can provide you with superior results. We
also recommend that you will have the best results by consulting a professional installer,
but If choosing to do your own installation, please note the following:

   Make sure all moving parts and factory electrical wires are out of your way and will not

interfere after installation.

   Leave a little slack in the wire to prevent pulling or stretching, this is even more

important if the wires will be run under or through the factory interior.

   Use tie downs and wire clamps to prevent the wires from getting caught or shorted.

   We do not recommend placing or installing band pass enclosures where they might be

subjected to moisture.

   Correct subwoofer polarity must be observed.  The polarity positive side is marked by a

(+) sign. Subwoofers out-of-phase will have little bass output.

   Correct 12 volt polarity for lighting elements must be observed.  Failure to maintain

correct polarity will not provide the needed DC power  needed to illuminate the lighting 
elements. Illumination inputs are 12 volt only.  Do not connect an amp or any audio 
output source to the lighting (Illuminite) inputs.  Doing so will cause permanent damage
to the lighting elements.

   Speaker wire should be isolated from the vehicle's electrical system to avoid noise

being picked up by the amplifiers.

   Speaker wire should be large enough to carry the full power of your amplifier. 14 gauge

or larger sizes are adequate.

   Be sure to give your ears consideration. Listening to loud music for extended periods

can possibly damage your hearing!

Summary of Contents for XNBP









Reviews: