manualshive.com logo in svg

Dspecialists ISOSTEM Expert, User Manual

Share
Download
Dspecialists ISOSTEM Expert User Manual Download Page 38

ISOSTEM     USER MANUAL

38     GUI Software Reference

Delta Frequency

Half width of the transition region.

Unit: Hz
Range: 0 Hz .. 234 Hz in steps of 23 Hz

LFE -10dB attenuator (Dolby/DTS)

Activates a 10 dB attenuation at the LFE output.

Extra Sub to LFE

The fader „Extra Sub to LFE“ controls the amount of additional bass, which
is extracted from the stereo reference signal and which is mixed to the LFE
channel of the output bus.

Unit: dB
Range: 0 dB..-inf

Please note:

 See

Appendix B: Schematic Block Diagram

.

Extra Sub to LFE Mute & Fade

Mute deactivates the extra bass. Solo mutes all other mute / solo controls.
This is useful to monitor the complete signal without the extra bass.

HCF Window

The HCF window features a high frequency attenuator on the rear channels
that allows the user to polarize the image and
reinforce the attraction of the front channels.
Just like "SUB", this filter acts on the spectral
envelope with a gain in amplitude and constant
phase. This filter applies to the internal bus at
the end of the Panoramic Analyzer and Virtual
Microphone.

Options:

Cut Frequency (0 Hz – 20 kHz)
Delta Frequency (0 Hz – 20 kHz)
Attenuation level (0 dB - -inf)

Summary of Contents for ISOSTEM Expert






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands