D E E P S E A E L E C T R O N I C S
8 7 1 x I N S T A L L A T I O N I N S T R U C T I O N S
ACCESSING THE FRONT PANEL CONFIGURATION EDITOR
NOTE:
NOTE:
NOTE:
NOTE: Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor.
comprehensive module configuration is possible using the
comprehensive module configuration is possible using the
comprehensive module configuration is possible using the
comprehensive module configuration is possible using the PC C
PC C
PC C
PC Configuration
onfiguration
onfiguration
onfiguration
S
S
S
Software
oftware
oftware
oftware.
.
.
. Please contact us for further details
Please contact us for further details
Please contact us for further details
Please contact us for further details....
•
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
•
Press the Stop/Reset
and Info
buttons simultaneously.
•
If a module security PIN has been set, the PIN number request is then
shown :
•
Press
, the first ‘#’ changes to ‘0’. Press
(up) or
(down)
correct value.
•
Press
(right) when the first digit is correctly entered. The digit you have just entered will now
show ‘#’ for security.
•
Repeat this process for the other digits of the PIN number. You can press
to move back to adjust one of the previous digits.
•
When
is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
not correct, you must re-enter the PIN.
•
If the PIN has been successfully entered (or the module PIN has not been
enabled), the editor is displayed :
EDITING A PARAMETER
•
Enter the editor as described above.
•
Press the left or right buttons to cycle to the section you wish to view/change.
•
Press the up
or down
buttons to select the parameter you wish to view/change within the currently
selected section.
•
To edit the parameter, press
to enter edit mode. The parameter begins to flash to indicate that
you are editing the value.
•
Press the up
or down
buttons to change the parameter to the required value.
•
Press
to save the value. The parameter ceases flashing to indicate that it has been saved.
•
To exit the editor at any time, press and hold the
button.
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
ensure
ensure
ensure
ensure security.
security.
security.
security.
NOTE:
NOTE:
NOTE:
NOTE: The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
a
a
a
au
u
u
utttto
o
o
om
m
m
ma
a
a
attttiiiic
c
c
ca
a
a
alllllllly
y
y
y)))) tttto
o
o
o e
e
e
en
n
n
ns
s
s
su
u
u
urrrre
e
e
e s
s
s
se
e
e
ec
c
c
cu
u
u
urrrriiiitttty
y
y
y....
D E E P S E A E L E C T R O N I C S
8 7 1 x I N S T A L L A T I O N I N S T R U C T I O N S
053-071
ISSUE 1
Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor.
Selected parameters can be configured via the front panel editor. More
More
More
More
onfiguration
onfiguration
onfiguration
onfiguration Suite
Suite
Suite
Suite
Ensure the engine is at rest and the module is in STOP mode by pressing the Stop/Reset
button.
(down) to adjust it to the
when the first digit is correctly entered. The digit you have just entered will now
Repeat this process for the other digits of the PIN number. You can press
(left) if you need
is pressed after editing the final PIN digit, the PIN is checked for validity. If the number is
If the PIN has been successfully entered (or the module PIN has not been
Press the left or right buttons to cycle to the section you wish to view/change.
buttons to select the parameter you wish to view/change within the currently
to enter edit mode. The parameter begins to flash to indicate that
change the parameter to the required value.
flashing to indicate that it has been saved.
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
NOTE: When the editor is visible, it is automatically exited after 5 minutes of inactivity to
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
The PIN number is automatically reset when the editor is exited (manually or
