DS Automobiles DS 4 Handbook Download Page 71

Page: 71 / 421

Access

In the event of a malfunction with the remote
control, you can no longer unlock, lock or
locate your vehicle.

First of all, use the key in the lock to unlock

or lock your vehicle.

Then, reinitialise the remote control.

Fault with the remote control

Reinitialisation

Switch off the ignition and remove the

ignition key.

Press the closed padlock immediately for a

few seconds.

Turn the key to position

2 (Ignition on)

Switch off the ignition and remove the key

from the ignition switch.

The remote control is fully operational again.

Changing the battery

Battery ref.: CR2032/3 volts.

Unclip the cover using a small screwdriver

at the two cutouts.

Lift off the cover.

Remove the flat battery from its location.

Fit the new battery into its location

observing the original direction of fitment.

Clip the cover onto the casing.

If the battery is flat, you are informed
by illumination of this warning lamp,
an audible signal and a message in
the screen.

If the problem persists, contact a
CITROËN dealer as soon as possible.

Summary of Contents for DS 4






































































































































































































































































































































































































































Search results

Summary of Contents for DS 4

Reviews:

Brands by name

Popular brands

DS Automobiles DS 4, Handbook

Search results

Summary of Contents for DS 4

Reviews:

Brands by name

Popular brands