manualshive.com logo in svg

DS Automobiles DS 4, Handbook

Share
Download
DS Automobiles DS 4 Handbook Download Page 229

07

227

Practical information

Fuel

Capacity of the tank: approximately

 60 

litres.

Low fuel level

When the low fuel level in the 

tank is reached, this warning lamp 
comes on in the instrument panel, 
accompanied by an audible warning 

and the display of an alert message. 
When it first comes on, 

around 

6 litres

 of fuel remain in the tank.

Refuelling

F

  Press this button until the automatic 

opening of the fuel flap is heard.

 

This button remains active for a few 
minutes after switching off the ignition. If 
necessary, switch the ignition on again to 
reactivate it.

F

  Take care to select the pump that delivers 

the correct fuel for your vehicle.

If your vehicle is fitted with Stop & 
Start, never refuel with the engine in 
STOP mode; you must switch off the 
ignition using the key, or the START/
STOP button if your vehicle has 
Keyless Entry and Starting.

Additions of fuel must be of at least 5 litres to 
be registered by the fuel gauge.
Opening the filler cap may result in an inrush of 
air. This vacuum is entirely normal and results 
from the sealing of the fuel system.

Until sufficient fuel has been added, every time 
the ignition is switched on, this warning lamp 
appears, accompanied by an audible signal 
and an alert message. When driving, this 
audible signal and alert message are repeated 
with increasing frequency, as the level drops 
towards 

0

.

You must refuel as soon as possible to avoid 
running out.
For more information on 

Running out of fuel 

(Diesel)

, refer to the corresponding section.

Summary of Contents for DS 4






































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands