manualshive.com logo in svg

DS Automobiles DS 4, Handbook

Share
Download
DS Automobiles DS 4 Handbook Download Page 186

06

184

Driving

Driving recommendations

Observe the driving regulations and remain vigilant whatever the traffic conditions.
Pay close attention to the traffic and keep your hands on the wheel so that you are ready to react at 
any time to any eventuality.
As a safety precaution, the driver must only carry out actions requiring sustained attention when 
the vehicle is stationary.
On a long journey, a break every two hours is strongly recommended.
In difficult weather, drive smoothly, anticipate the need to brake and increase the distance from 
other vehicles.

Never drive with the parking brake 
applied - Risk of overheating and 
damage to the braking system!
Risk of fire!
As the exhaust system of your vehicle 
is very hot, even several minutes 
after switching off the engine, do not 
park or leave the engine running over 
areas where inflammable substances 
and materials are present: grass, 
leaves, etc.

Never leave a vehicle unsupervised 
with the engine running. If you have 
to leave your vehicle with the engine 
running, apply the parking brake 
and put the gearbox into neutral or 

position 

N

 or 

P

, depending on the type 

of gearbox.

Driving on flooded roads

We strongly advise against driving on flooded 
roads, as this could cause serious damage 
to the engine or gearbox, as well as to the 
electrical systems of your vehicle.

Important!

-  check that the depth of water does not 

exceed 15 cm, taking account of waves 
that might be generated by other users,

-  deactivate the Stop & Start system,
-  drive as slowly as possible without 

stalling. In all cases, do not exceed 6 mph 
(10 km/h),

-  do not stop and do not switch off the 

engine.

If you are obliged to drive through water:

On leaving the flooded road, as soon as 
circumstances allow, make several light brake 
applications to dry the brake discs and pads.
If in doubt on the state of your vehicle, contact 
a CITROËN dealer or a qualified workshop.

Summary of Contents for DS 4






































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands