background image

 

Copyright © 2001-2018, Dr Robot Inc.  All Rights Reserved.

    www.DrRobot.com              

     V.07.08.18.Q                   

- 24 - 

Joint3(Motor 

Driver board 2 

channel 1) 

Encoder :   One circle count is 3724 
                      Angle Resolution: 3724/ (2*PI) 
                                             
This joint is working in position control mode(mode 3): 
For example: 
                        Command:  !PR 1 -200\r  
                         It  will drive this joint to right. 
                       Command:  !PR 1 200\r  
                        It will drive this joint left. 
                        Command:  !P 1 -250\r  
                        It will drive this motor to encoder position -250.(make sure you know where it is 
and not in stuck state) 
On control board, we set current limitation for this joint.  It will enter emergency stop state 
when current is over 8A or current over 5A for over 1000ms. 
You could read temperature sensor via analog channel 3(AI 3). 
The temperature sensor is B57164K103J, you could find how to convert the readings  to 
temperature from the sample codes. 

 

Gripper(Motor 
Driver board 2 

channel 2) 

Encoder :   One circle count is 756 
                      Angle Resolution: 756/ (2*PI) 
                                             
This joint is working in open loop control mode(mode 0): 
For example: 
                        Command:  !G 2 -200\r  
                         It  will drive Gripper close. 
                       Command:  !G 2 200\r  
                        It will drive Gripper open. 
                        Command:  !G 2 0\r  
                        It will stop this motor.(make sure you send this command to stop the Gripper 
before it reaches  mechanical limitation) 
On control board, we set current limitation for this joint.  It will enter emergency stop state 
when current is over 2A or current over 1A for over 1000ms. 
You could read temperature sensor via  analog channel 4(AI 4). 
The temperature sensor is B57164K103J, you could find how to convert the readings  to 
temperature from the sample codes. 

 

 

 

Advanced Development 

Please refer to document “GPS-IMU Sensor Module and Outdoor Autonomous Navigation Program” for detail on 
autonomous navigation programming using the Jaguar GPS and IMU system module. 

Support  and  sample  codes  are  available  for  using  OpenCV,  LabVIEW  and  MATLAB.  Please  contact 

support@drrobot.com

 for further information.   

 

 

 

Summary of Contents for Jaguar 4x4

























Reviews: