manualshive.com logo in svg

DriSteem MP, Installation, Operation And Maintenance Manual, Page: 13 / 32

Share
Download
DriSteem MP Installation, Operation And Maintenance Manual Download Page 13

11

ULTRA-SORB MP INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Airflow

DC-1081_2020AA

FIGURE 11-1: PLACING A DISPERSION ASSEMBLY IN A DUCT

C

AIRFLOW PROVING SWITCH

Ensure placement is representative of air to dispersion device. Sail switch 
recommended for variable air volume applications. Pressure switch 
recommended for constant volume applications.

DUCT HIGH LIMIT

Place high limit as far downstream as possible but before a duct transition to 
prevent wetting again duct walls or other components within the airstream. 
General recommendation is 8'-12' (2.4 to 3.7 m) downstream.

PLACEMENT IN A DUCT

Location C is the best choice. Air leaving a fan is usually very turbulent and 
can cause vapor to not absorb at the expected non-wetting distance. Allow for 
more distance if installing downstream from a fan.

Calculated absorption distances assume even airflow across entire dispersion 
device.

INSTALLATION

Horizontal duct

Duct 

high limit 

humidity 

control

Airflow 

proving 

switch

Summary of Contents for MP

































Reviews:

No comments